Development News

  • 2018: research article on angular sensor with feedback
    2018: research article on angular sensor with feedback

    The article reports on development of a precision angular molecular-electronic accelerometer with a magnetohydrodynamic cell for creation of a negative feedback and optimization of electronics for creation of a feedback signal. The main characteristics of the angular accelerometer such as an amplitude-frequency characteristics, self-noise and Allan variance were experimentally measured. 

    Results of comparison of the obtained output parameters to analogs showed prospects for further development in this field.
  • 2017: presentation of seismometer for asteroid, NASA files
    2017: presentation of seismometer for asteroid, NASA files
    An amazing presentation titled 'APEX - Asteroid Probe Experiment' given at The Small Satellite Conference by our colleagues from Johns Hopkins University, University of Maryland and Arizona State University describing a possible placement of a molecular-electronic seismometer on the surface of Apophis asteroid.

    Watch the original presentation available on the NASA website.
  • 2017: NDAS data loggers launched
    2017: NDAS data loggers launched
    The data loggers' product line was enriched with the products by NordLab LLC - a joint enterprise of R-sensors and MIPT. The new data loggers are named NDAS. They exploit the latest ARM architecture Texas Instruments' controller and a multichannel ADC by Analog Devices. 

    Low power consumption and wireless Wi-Fi interface for setup and signal quality control are but two distinctive features of NDAS. A GPS/Glonass combined receiver provides coordinates and clock synchronization.

    The current product line is constituted by the 4-channel low-power autonomous data logger module NDAS-8224 and the 6-channel multi-purpose data logger NDAS-8226. The 12- and 48-channel versions are under development. The data loggers can be equipped by an accelerometer and a magnetic compass which allow determination of azimuthal orientation and tilt with respect to vertical direction as well as by temperature, pressure and humidity sensors for checking the working conditions and impermeability in case of a submerged deployment. All auxiliary information from sensors is available in telemetric transfer from the data logger as well as it is stored along with the registered signal. 

    The full compatibility with R-sensors' seismic sensors was of most importance during the development of the data loggers. A joint project of R-sensors and NordLab for the design of seismographs - seismic sensors with a data logger inside - is now being developed.
  • 2017: article on subsea seismic station NDAS-8224SBS
    2017: article on subsea seismic station NDAS-8224SBS

    This paper reports on a field testing of the subsea autonomous seismic station NDAS-8224SBS which has a modular structure allowing for operations under different environmental conditions like onshore, offshore to a 500-meter depth and in transition zones. The station operation frequency band is 300 Hz which is wider than that of the majority of seismic stations based on standard (10 Hz) geophones.
  • 2017: article on accelerometers MTSS-1033A
    2017: article on accelerometers MTSS-1033A

    This paper reports on the development of the feedback system for a MET seismic accelerometer, a feedback stability analysis and optimization of the signal conditioning feedback electronics to get the highest dynamic range. The article is focused on the operation principles of the MTSS-1033A seismic accelerometer and contains the latest comprehensive analysis of the noise generation mechanisms which occur in molecular-electronic transducers.
  • 2016: two articles on MET sensors
    2016: two articles on MET sensors


    Both articles were written by our colleagues and are covering the latest results of the MET sensors studies gained in MIPT laboratories in 2015 - 2016.
  • 2016: strong motion modification of METR-01
    2016: strong motion modification of METR-01
    The modification of the one-component rotational sensor METR-01 was designed and successfully tested. 

    The modified sensor has a 1 rad/sec input signal range. To comply with the output voltage range, the sensitivity was reduced ten times down to 5 V/rad/sec. In order to do it, an additional thin ceramic paper was placed inside the sensing channel. Follow the link for a METR-01LS sensor tests presentation.
  • 2016: renewal of Baykal-CME seismic station
    2016: renewal of Baykal-CME seismic station
    The components of seismic station Baykal-CME were renewed. 

    The new DSP of Baykal-8 data logger allowed for recording the same signal at different sample rates simultaneously. The recording of signal with reduced sampling permits a quick amplitude analysis to be performed on a long-term recording, which is highly demanded by seismologists. Apart from this, the output for applying periodical test signals to sensors was introduced. 

    The modification of the CME-6211 seismic sensor allowed for wide power supply options to be offered, namely from +5 to +36V DC which were earlier available only for the CME-6111 seismic sensor. Besides, the self calibration circuits were modified so the response curves for all three channels can be obtained. The circuits were optimized for interaction with Baykal-8 data logger.
  • 2016:
    2016: 'Instrumentation in Earthquake Seismology' published
    Springer Publishing House published a second edition of 'Instrumentation in Earthquake Seismology'

    The chapter on 'Some New Trends in Seismic Sensors' covers a description of modern electrochemical transducers of linear and angular motion. The CME-6211 - a top model among the seismometers produced by R-sensors - is listed on the summary table of 'Overview of some active sensors available on the market'.
Pages:
Prev. Next